Templar's Gear Vest Pack H1 Hydration Carrier with PALS and Quick Attachment, Ranger Green (Strap Attachment)

Vest Pack - Baby Got Back Templar's Gear Vest Pack is a backpack panel that attaches to the back of a plate carrier (or any vest, really). This is awfully handy for a hydration carriers, but one can fit here just about anything (with the bladder)! Moreover, with a separate adapter, this is extremely easy to swing forward, which makes it easy to go through the contents yourself. Do you have to change the radio frequency on the fly? Easypeasy! Hangry and munchies are on your back? Easypeasy! Caught in the rain and the rain cloak is in the pack? Easypeasy! The corners of the Vest Pack have D rings to which the parts of the separate adapter attach. By opening the buckles, the entire pack can be swung forward over the head, or by opening one shoulder buckle, the pack comes forward by either side. With the adapters, the Vest Pack can also be attached to, for example, a bergen, from where it can be transferred to the back of the vest as a daypack. In addition, the Vest Pack has PALS loops, so it fits any PALS matrix with at least six horizontal and five vertical loops. Even with less, it will stick. In principle, there is no need to have loops in the middle, as long as there are enough loops on both sides!Also available is the big brother Vest Pack H2, that has around litre and a half more capacity. Features: Attaches directly with the PALS/MOLLE loops to any vest, or for example to a zippered back panel, so the removal is quick! If you use straps or the Vest Pack adapter, you can detach the PALS loops. The space requirement is 6 x 5 PALS loops. The center can be clean.However, the real magic tool is the much acclaimed Vest Pack adapter, which attaches the pack to the vest with buckles. By opening the side buckles, the entire system can be swung over the head to the front, allowing the content to be accessed without pleading for support from your battlebuddy. You can also open one of the shoulder buckles and swing it to the front by the side if you're wearing a helmet or something. The adapters are attached to the D rings in the corners, to which the any straps can also be attached. (If the Ranger Green adapter is out of stock, we might have some M05 adapters in stock.)Stiffened back - reduces ballooning and sagging in generalA spacious mouth with inlets for tubes and cables on both sidesA simple hydration bladder pocket inside the main compartment with a hanging loop. The three-liter WLPS bladder is a little tight, and the closure bar has to be folded inward. Inside the main compartment there is also an organization pocket with a zipper closure, depth is about 14 cm and width 22 cm.Strong elastic cord on the sides for tidying the contents and/or overpacking. The adjustment is done with cord locks.On the top are two zippered pockets with access from the side: both sized approx. 16 x 27 cm, mouth approx. 19 cm.4 x 4.5 PALS matrix on top. Thanks to the laser cutting, the "middle rows" can be used too. Also on top there is a 16 x 6 cm loop velcro matrix.500D Cordura as the main material. Buckles are of high quality and made by Woojin from Korea. Do we really have to say from which Korea? Weighs 310 g. It is very little, considering how sturdy this good boy is. The (outer) dimensions are approximately 23 × 28 × 6.5 cm. The plumpness factor is greatly influenced by the packaging style and the packaged item(s). With street mathematics the estimated volume is just under 4 liters. Do you need more capacity? 'ere ya go! Templar’s Gear – laser cut quality Templar’s Gear represents the renaissance of European military gear manufacturers that began in the 21st century. American manufacturers dominated the tactical gear market for a long time, but the Old World was not yet ready to throw in the towel. In this continuum, Templar’s Gear represents the leading edge of high-quality, modern and well-designed gear. The defining characteristic of the company is that their products are manufactured using laser cutting and 500 denier Cordura, which makes the products a lot lighter without compromising reliability. Special attention has been paid to quality control in Templar’s pouches and gear, because a significant portion of the company’s customers are officials, whose safety and well-being might depend on the gear. The materials used by Templar’s Gear are IRR protected, so the user won’t glow in the night vision devices like a Ukrainian firefighter. Cooperation - Yhteistyö - Współpraca Templar's Gear products are delivered to us straight from the factory in Poland. This means that our product selection is updated to the latest and greatest generation almost in real time as replenishments are ordered. Thanks to the close cooperation and our frequent orders, we also have a chance to forward feedback and new ideas to the respective designers. If you as a user have any ideas for product development, we are happy to share them with Templar's Gear. Extended three-year warranty Templar’s Gear products are granted a three-year warranty. In more concrete manner this means that for example products sold this spring will have warranty for three action packed seasons of airsoft, shooting or whatever you decide to do with them. The warranty covers all problems that might arise from defective materials or poor craftsmanship. Carelessness or misuse voids the warranty.